Closed-Cell Spray Foam Insulation in Toronto, ON
Dense, rigid foam for rim joists, brick and stone walls, and the shallow roof cavities you find in older Toronto houses.
We install closed cell spray foam insulation in Toronto's older homes, mostly the Victorian and Edwardian semis in the west end. Closed-cell is the dense, rigid type of spray foam insulation. One layer of it seals air, insulates and holds back vapour, so it's what we use against brick and stone, on rim joists and in shallow ceiling cavities.
What closed-cell foam does that other insulation can't
Closed-cell foam cures into a dense, rigid layer that stops air, slows vapour and insulates, all in one material. Fibreglass batts and loose cellulose slow heat, but air passes through them. They need a separate air barrier and a plastic vapour retarder to finish the job. Closed-cell foam does both of those jobs on its own.
This matters most against masonry. Brick and stone stay cold all through a Toronto winter, and when warm indoor air reaches them it leaves water behind as condensation. The foam bonds to the masonry, so there's no gap for that air to get into, and the wet layer never forms behind the insulation.
Open-cell foam is the softer, lighter type. It seals air well but lets vapour through, so it goes in different places from the ones on this page.
Where closed-cell goes in an older house
Closed-cell is worth it where space is tight, where the surface behind it is cold, or where both air and moisture need stopping. Below are the spots where we pick it over other insulation, and why.
Rim joists
We spray closed-cell foam on the rim joists, where the floor joists end on the foundation. Each bay is a small box cut up by joist ends, the sill plate, wires and pipes. Cut batts or boards leave gaps around every edge. The foam fills those edges and seals the air leaks at the same time, and it keeps warm air off the cold wood.
Against brick and stone
Where an interior wall is bare brick or a stone foundation, closed-cell is the foam we put against it. It resists vapour, so indoor moisture stays off the cold masonry. It also sticks to rough, uneven surfaces where a rigid board would never sit flat.
Shallow roof and ceiling cavities
Sloped ceilings, knee walls and flat-roof additions often have only a shallow cavity between the roof deck and the drywall. Closed-cell gives you more R-value per inch than batts, so you get the most insulation into a space that can't be made any deeper. It also keeps moist house air away from the cold underside of the roof deck.
Below-grade walls
On a foundation wall below grade, we spray closed-cell once the wall is dry. The foam doesn't soak up water the way fibreglass does, and it replaces the plastic sheet a framed and batted wall would need.
Closed-cell foam on the inside of a brick wall
Closed-cell foam can go straight onto the inside face of a brick wall. It resists vapour enough to handle the cold-weather condensation that forms where foam meets brick, according to Building Science Corporation's digest BSD-114 on insulating load-bearing masonry walls in cold climates.
Sprayed right onto the masonry, the foam becomes the airtight layer and controls condensation from air leaks. It follows old mortar joints, patches and rough brick without leaving a pocket behind it.
Before we spray anything, we deal with the wall's wet spots. Water usually gets in at the corners under window sills and in the brick near grade. Foam sprayed over a damp patch just hides the problem.
Not every brick wall in an old semi should be sprayed. Our wall insulation page covers the other ways we insulate walls, including dense-packing through small holes that we patch afterwards.
Thickness and R-value
BSD-114 puts 2 inches of closed-cell spray foam at about R-12. The exact number varies by product, so we use the data sheet for the foam we're spraying, not a rule of thumb.
Your quote lists the thickness for each spot. Put that next to the data sheet and you can see what R-value each part of the house is getting.
Covering the foam
Spray foam inside the house has to be covered, and a drywall finish over it gives the foam its fire protection. Plan the covering when you plan the foam, whether that's drywall over a basement wall or a finished sloped ceiling.
Nobody should be in the work area while we spray or while the foam cures. We ventilate the space during the job and let you know when you can use it again.
What a closed-cell quote should name
A closed-cell quote should list every spot, the thickness at each one, and the work done before and after spraying. A vague quote makes it hard to compare one contractor with another.
Spray foam prices depend on these same details. Our spray foam insulation cost page explains how they add up.
A good quote is detailed enough that another crew could pick it up and do the same job. Check that it covers:
- Each spot by name, like the rim joists along the front wall, the knee wall behind a bedroom or the sloped ceiling in a flat-roof addition.
- The thickness in inches at each spot.
- The R-value for that thickness, from the data sheet of the product being sprayed.
- Prep: what gets cleared, cleaned or repaired first, including wet spots on brick and stone.
- Covering: whether drywall goes over the foam, and who puts it up.
- Ventilation during the job, and when the space can be used again.
FAQ
Common questions about closed-cell spray foam
Closed cell spray foam is used where a single layer has to insulate, stop air and hold back vapour: rim joists, the inside of brick and stone walls, and shallow sloped or flat ceilings. Once cured it's dense and rigid, so it fits more insulation into a thin space than batts can. In an older house, it's most useful against cold masonry.
Yes. Closed-cell spray foam resists vapour enough to handle cold-weather condensation where it meets brick, so it does the vapour barrier's job there. A wall sprayed with it doesn't need a separate plastic sheet. Open-cell foam lets vapour through, which is the main reason the two foams go in different places.
Closed-cell spray foam should be thick enough to give each spot the R-value it needs, and your quote should state that thickness in inches. Building Science Corporation's BSD-114 puts 2 inches at about R-12. The exact R-value comes from the data sheet for the product being sprayed.
Yes, once any water coming through the wall has been dealt with. The foam follows the uneven stone and mortar and seals the air leaks between them. It won't stop water coming in from outside, so the wet spots get fixed first, and drywall goes over the foam afterwards.
Get a Quote
Get a spray foam insulation quote in Toronto
Tell us the address and which part of the house bothers you, whether that is a cold top floor, a drafty basement or a ceiling with no attic above it. Phone or use the form. We'll set up a time to look at the house, then give you a written quote.