We install loose fill insulation across Toronto, blown through a hose onto attic floors and into closed wall cavities. The material is cellulose or fibreglass, and it settles in around joists, wiring and awkward framing, filling the gaps that cut batts leave behind. If you have an open attic floor with room for depth, it does the job for less than spray foam. That is usually why we recommend it there.

How loose-fill goes in

Loose-fill goes in through a hose from a blowing machine parked outside, usually in the driveway. The machine breaks up compressed bales of cellulose or fibreglass and pushes the loosened material along a long hose that runs through the house and up to the attic hatch. Before we start, we put drop sheets down along the hose route and cover the floor under the hatch, so the path from your front door to the attic stays clean.

Up in the attic, one of our crew moves the hose end across the floor while the machine outside keeps feeding it. The insulation lands between the ceiling joists and piles up around wiring, junction boxes, plumbing vents and all the blocking older framing tends to have. A batt has to be cut to fit around each of those, and every cut leaves a gap. Blown-in material just flows around them. That makes it a good fit for the cramped, uneven attics in older semis, where you can barely crawl out to the eaves.

Cellulose or fibreglass

Both work well as loose-fill, and neither one wins every time. It comes down to your attic and what is already up there.

Blown-in cellulose

Blown-in cellulose insulation is recycled paper treated with a fire retardant. It is dense, so it packs in around wiring and fills small voids well, and that density also slows down air moving through it. It weighs more than fibreglass for the same coverage, and it does not handle water: if the roof leaks, the cellulose mats down and the wet section has to be pulled out.

Blown-in fibreglass

Blown-in fibreglass is loose, light spun glass fibre. You need more depth of it than cellulose to reach the same R-value, but it puts less weight on an old plaster ceiling and it does not soak up water the way paper does. If your roof has leaked before, fibreglass dries out and recovers better once the leak is repaired.

When loose-fill beats spray foam

Loose-fill wins on an open attic floor with enough height to build up depth. If the ceiling joists are exposed and the hose can reach every corner, blown-in material gets to the target depth for less money than spraying the same area. A loose fill attic floor is also easy to top up later, and easy to push aside when an electrician needs to get at a box.

Spray foam still has a place in the same attic. We use spray foam insulation where loose-fill cannot seal: the tight edges where the roof meets the wall, the gaps around a brick chimney, the openings around plumbing stacks. Foam sticks to the framing and stops air. Loose-fill sits on top and slows heat. In an older house, attic insulation work often uses both, each in the spot it handles best.

Air sealing and baffles before the hose goes up

Air sealing comes first, before any loose-fill goes down. Warm, damp air from the house leaks into the attic through gaps in the ceiling: around light fixtures, through wiring holes in the top plates, past the attic hatch, and up the chases beside chimneys and stacks. Loose-fill slows heat, but air passes straight through it. Leave those gaps open and the house keeps losing warm air, and in winter the moisture in that air can frost up on the underside of the roof deck. So we seal the attic floor, then blow the insulation over it.

Baffles go in at the eaves before we start blowing. A baffle is a channel fixed between the rafters above the outside wall. It holds the insulation back and keeps a clear path for air coming in from the soffit vents. Without baffles, blown-in material drifts into the soffits and blocks the airflow that keeps the roof deck dry. Some eaves are too tight to reach, and in that case we work out how to keep the ventilation open when we look at the attic before quoting.

Dense-pack: loose-fill inside closed walls

Dense-pack is loose-fill blown into a closed wall cavity so tightly that it can't slump. We dense-pack wall insulation through small holes and patch them afterwards, so your plaster or siding stays where it is. The hose goes into each cavity and fills it from the bottom up, packing in around wiring and the blocking between studs.

Whether a wall can take it depends on what's inside. Before we quote wall insulation, we check how the wall is built:

  • Suits dense-pack: a wood-frame wall with an empty stud cavity between the plaster or drywall inside and the sheathing outside.
  • Suits dense-pack, with prep: a balloon-framed wall, once we close off the bottom of each open stud bay so the material stays in the wall and doesn't fall through to the basement.
  • Doesn't suit it: solid brick with no cavity, including double-brick walls where the two layers sit tight together. There's nothing to fill, so those walls get insulated on the inside face instead.
  • Needs a closer look: a cavity that already has old batts or slumped insulation in it, because the hose can't pack tightly around them.

Depth markers and what to check afterwards

Depth markers are printed rulers we staple to the ceiling joists before the insulation goes in. They're spread across the attic floor and turned to face the hatch, so you can read the installed depth without stepping onto the ceiling. After a loose-fill job, this is how to read them:

  • Stand at the hatch with a flashlight and find the nearest marker and the farthest one.
  • Note the figure at the surface of the fill on each marker and set it against the depth written on your quote.
  • Check that the surface looks level between markers. A low patch near the hatch or the eaves means someone walked on it or the material drifted.
  • Have another look after the first winter. The markers will show you how much it has settled.

Depth targets and settling

The building code sets insulation targets for new houses, and they're a handy yardstick for an older attic too. For a new house in Zone 1, SB-12 sets R-60 as the minimum for a ceiling with attic space in compliance packages A1, A2, A4 and A6, and R-50 in packages A3 and A5. SB-12 covers new construction only, but it gives you a sense of how deep a well-insulated attic floor ought to be.

Settling is why the markers matter. Loose-fill loses some height in the months after it goes in, and loses some R-value along with it. A marker lets you see that happen, so deciding on a top-up means reading a number off a ruler instead of guessing.

Rebates for loose-fill attic work

Attic insulation is one of the Home Renovation Savings rebates that doesn't require a home energy assessment. You don't have to book a before-and-after audit,. Terms and eligibility rules apply and can change, so check the program's current conditions before work starts. When we come out to see your attic, we can go through what the program asks for along with what the attic needs.

FAQ

Common questions about loose-fill (blown-in) insulation

Not in every attic. Cellulose is denser and packs tighter around wiring and framing. Fibreglass is lighter and handles moisture better. We pick one based on the ceiling underneath and whether the roof has leaked before.

Yes, as long as the old material is dry and in good shape. We blow the new layer straight on top to build up the depth. If the old insulation is wet, matted or torn up by raccoons, it has to come out first. If it looks like vermiculite, a grey-brown pebbly fill, leave it alone and get it tested by a qualified lab or abatement firm before anyone disturbs it.

Yes, it settles a bit after it goes in, and the depth markers on the joists show you by how much. That's why we fill an attic with some allowance for settling. Dense-pack in walls goes in tight enough that it stays put in the cavity.

Yes, in walls with a closed cavity to fill. We dense-pack it through small holes and patch them afterwards. Solid brick walls have no cavity, so they can't take it and need a different approach.

Get a Quote

Get a spray foam insulation quote in Toronto

Tell us the address and which part of the house bothers you, whether that is a cold top floor, a drafty basement or a ceiling with no attic above it. Phone or use the form. We'll set up a time to look at the house, then give you a written quote.

Call Text Quote