Rim joist insulation in Toronto seals and insulates the band of framing where the floor joists end on top of the foundation. In a lot of houses the rim leaks more air than anything else in the basement, so it can be done by itself or as part of full basement insulation. If your basement is cold and drafty, it's worth a look. In older brick homes it usually matters most.

What and where the rim joist is

The rim joist is the board that runs around the edge of the floor frame and caps the ends of the floor joists where they sit on the foundation. To find it, stand in the basement and look up to where the foundation wall meets the floor above. You'll see a row of joist ends, a horizontal board closing them off, and under that a sill plate resting on top of the wall. Plenty of trades call it the header, so header insulation and rim joist insulation are the same job.

Not every older house has one. Where the walls are load-bearing brick, the floor joists often end in joist pockets left in the brick rather than on a wood sill, and there may be no rim board at all. Each joist end sits in its own small cavity in the masonry, and that changes how the space should be sealed.

Why the rim joist leaks

The rim joist leaks because several materials meet there and none of the joints were built airtight. Wood shrinks and moves. Concrete, stone and brick don't. Over time gaps open between the sill plate and the foundation, and between the rim board and the sill.

  • The sill joint: where the sill plate sits on the foundation, often with nothing between them to seal it.
  • The rim seams: the joints above and below the rim board, where it meets the sill and the floor sheathing.
  • Wiring and pipe holes: every cable, gas line, hose bib and dryer vent through the rim leaves a gap, and those gaps are rarely sealed.
  • Mortar gaps: in brick and stone foundations, the mortar near the top of the wall crumbles and opens a path to the outside.

Spray foam at the rim joist

Rim joist spray foam is the most complete fix for a wood rim, because one material handles both the air sealing and the insulating. Closed-cell foam goes on as a liquid, expands into the gaps between the rim board, the sill plate and the foundation, and cures into a rigid layer in a single pass.

We spray each bay between the floor joists on its own, working the foam into the corners and around wires and pipes so it fills the gaps instead of bridging over them. Closed-cell spray foam also holds up against moisture, which matters for wood sitting against cold masonry. Before we spray, we check the rim for soft or water-stained wood. Foam seals a sound rim. It won't fix a rotten one.

Joist pockets in brick walls

Where wood beams rest in pockets in the masonry, the goal is to stop indoor air leaking into the cold pocket. Venting the pocket will almost certainly cause condensation: warm, damp air from the house reaches the cold brick around the joist end and leaves its moisture on the wood.

So we seal around joist ends instead of venting them. In the west end century semis we work on, we close the gap where each joist enters the brick from the inside, with foam or caulk depending on how big the gap is. The joist end stays bedded in the masonry, and basement air can't get to it anymore.

Board and sealant instead of foam

Rigid foam board, cut to fit and sealed on every edge, can work when there are only a few bays. Each piece is cut to sit snug against the rim, then every edge gets sealed to the joists, sill plate and subfloor with canned foam or caulk so air can't move behind it.

It makes sense for a handful of open bays where bringing in spray equipment would be overkill. The catch is that every wire, pipe and odd-sized bay means another custom cut. Miss one edge and warm air gets to the cold rim behind the board, and moisture builds up there.

Fibreglass or mineral wool batts stuffed into the bays by themselves don't do much. Batts slow heat loss, but air goes straight through them, so the rim keeps leaking and the cold wood behind the batt can collect condensation.

Checking your rim joists yourself

All you need to check your rim joists is a cold, windy day and a flashlight. Run the light along the top of the foundation wall into each bay between the floor joists, and look for these.

  • Drafts: hold the back of your hand near the sill plate and around pipes and wires. If you feel cold air moving, there's a gap to the outside.
  • Cobwebs that move: webs swaying in a bay when nobody's near them tell you air is passing through.
  • Frost on the wood or nail heads: moisture from inside the house is reaching cold wood and freezing, so that bay leaks and needs sealing.
  • Dark stains on the rim or sill: usually repeated condensation or water. Press the wood with a screwdriver. If it gives, the rot has to be dealt with before any insulation goes on.
  • Daylight at the sill joint: that's a hole straight through to the outside.

What to note before a rim joist visit

Write down which walls had drafts, frost or stains, and snap a few photos. Your notes help Premier Insulation Toronto find the worst leaks sooner.

FAQ

Common questions about rim joist insulation

Yes. In almost every heated house with a basement, the rim joists should be insulated and air sealed. The rim sits above grade with just a layer of wood between the basement and the outside, so it lets in drafts and loses heat. Sealing it also stops cold air from sliding down the basement walls.

For a wood rim joist, closed-cell spray foam is usually the best choice, because one layer air seals, insulates and fills irregular gaps. Rigid foam board sealed on every edge can also work when there are only a few bays. In brick walls with joist pockets, what matters most is sealing around each joist end so indoor air can't reach the cold pocket.

Not with batts alone, because air moves right through fibreglass and mineral wool. Without an air seal, warm indoor air gets to the cold rim and can condense on the wood behind the batt. If you use batts, put an air seal against the rim first, like rigid foam board with caulked edges.

Header insulation is another name for rim joist insulation. Many builders call the rim joist the header. Either way it means the band of framing at the top of the foundation wall where the floor joists end, and the job is the same: seal the air leaks, then insulate each bay.

Not always. Where a house has load-bearing brick walls, the floor joists can end in pockets in the brick instead of on a wood rim, and then the work is sealing around each joist end, not insulating a continuous board.

Get a Quote

Get a spray foam insulation quote in Toronto

Tell us the address and which part of the house bothers you, whether that is a cold top floor, a drafty basement or a ceiling with no attic above it. Phone or use the form. We'll set up a time to look at the house, then give you a written quote.

Call Text Quote